Home > CSC-OpenAccess Library > Manuscript Information
EXPLORE PUBLICATIONS BY COUNTRIES |
EUROPE | |
MIDDLE EAST | |
ASIA | |
AFRICA | |
............................. | |
United States of America | |
United Kingdom | |
Canada | |
Australia | |
Italy | |
France | |
Brazil | |
Germany | |
Malaysia | |
Turkey | |
China | |
Taiwan | |
Japan | |
Saudi Arabia | |
Jordan | |
Egypt | |
United Arab Emirates | |
India | |
Nigeria |
A Comparison of Optimization Methods in Cutting Parameters Using Non-dominated Sorting Genetic Algorithm (NSGA-II) and Micro Genetic Algorithm (MGA)
Abolfazl Golshan, Mostafa Rezazadeh Shidar
Pages - 62 - 73 | Revised - 01-09-2011 | Published - 05-10-2011
MORE INFORMATION
KEYWORDS
Cutting Parameters, Surface Roughness, Tool life Criteria, Optimizing, NSGA-II, MGA
ABSTRACT
Since cutting conditions have an influence on reducing the production cost and time and deciding the quality of a final product the determination of optimal cutting parameters such as cutting speed, feed rate, depth of cut and tool geometry is one of vital modules in process planning of metal parts. With use of experimental results and subsequently, with exploitation of main effects plot, importance of each parameter is studied. In this investigation these parameters was considered as input in order to optimized the surface finish and tool life criteria, two conflicting objectives, as the process performance simultaneously. In this study, micro genetic algorithm (MGA) and Non-dominated Sorting Genetic Algorithm (NSGA-II) were compared with each other proving the superiority of Non-dominated Sorting Genetic Algorithm over micro genetic since Non-dominated Sorting Genetic Algorithm results were more satisfactory than micro genetic algorithm in terms of optimizing machining parameters.
1 | Radhika, n., vijaykarthik, k., & shivaram, p. (2015). adhesive wear behaviour of aluminium hybrid metal matrix composites using genetic algorithm. Journal of Engineering Science and Technology, 10(3), 258-268. |
2 | Tamizi, M., Izman, S., Shirdar, M. R., Al-Mayyahi, N. N., & Parhizkar, S. (2015). Predicting Micro-Hardness of Post-Treated Hydroxyapatite Layer Using Surface Response Methodology. Journal of Soft Computing and Decision Support Systems, 2(1), 1-7. |
3 | Dhandapani, K., Vasanthkumar, P., & Nagarajan, S. (2014). A Meta-Heuristic Evolutionary Algorithm to Optimize Machining Parameters in Turning AISI 4340 Steel. Journal of Advanced Engineering Research, 1(2). |
4 | Margonis, S. (2014). Preliminary design of an autonomous underwater vehicle using multi-objective optimization (Doctoral dissertation, Monterey, California: Naval Postgraduate School). |
5 | Nayak, B. E. D. A. M. A. T. I. (2014). Multi-response optimization in machining: exploration of TOPSIS and Deng’s similarity based approach (Doctoral dissertation). |
6 | Ojo, O. O., Ogedengbe, T. I., & Kareem, B. (2012). Effect of Cutting Conditions on Release Time of Jobs Using Lathe Machine. International Journal of Engineering Innovation and Management, 2(3), 59-66. |
D. Kanagarajan, R. Karthikeyan, K. Palanikumar, J. P. Davim, Int. J. Adv. Manuf Tech. 36, 1124, 2008. | |
Debabrata Mandal., Modeling of electrical discharge machining process using back propagation neural network and multi-objective optimization using non-dominating sorting genetic algorithm- II, Journal of Materials Processing Technology 186, pp.154–162, 2007. | |
Dereli, D., Filiz, I.H., Bayakosoglu, A., Optimizing cutting parameters in process planning of prismatic parts by using genetic algorithms. International Journal of Production Research 39 (15), 3303–3328, 2001 | |
Hsu VN, Daskin M, Jones PC, Lowe TJ. Tool selection for optimal part production: a Lagrangian relaxation approach. IIE Trans; 27:417–26, 1995. | |
K. Palanikumar, B. Latha , V.S.Senthilkumar ,R.Karthikeyan, Multiple Performance Optimization in Machining of GFRP Composites by a PCD Tool using Non-dominated Sorting Genetic Algorithm (NSGA-II),Met. Mater. Int.,Vol.15, No. 2, pp. 249-258, 2009. | |
Krishnakumar, K., “Micro-Genetic Algorithms for Stationary and Non-Stationary Function Optimization,” SPIE 1196, Intelligent Control and Adaptive Systems, 1989. | |
M. Sivakumar and S. M. Kannan, Int. J. Adv. Manuf Tech. 32, 591, 2007. | |
M.Rozenek.M,J.Kozak,L.Dabrovwki,K.Lubkovwki, Electrical discharge machining characteristics of metal matrix composites,J.Mater.Process.Technol.109, pp.367-370, 2001. | |
N. Srinivas and D. Kalyanmoy, Jl. Evol. Comput. 2, 221, 1994. | |
N.Tosun, C.Cogun , H.Pihtili , "The effect of cutting parameters on wire crater sizes in WEDM", int. J . Adv. Manuf. Techonl., Vol. 21, pp. 857-865, 2003. | |
N.Tosun,C.Cogun, An investigation on wire wear in WEDM, j.Mater.Process.Technol.1349 (3) , pp. 273-278, 2003. | |
Pandey PPC, Pal S. In: Proceedings of the Third International Conference in Computer Integrated Machining Singapore, vol. 1, pp. 812–9, 1995 | |
Senecal P. K., “Development of a Methodology for Internal Combustion Engine Design Using Multi-Dimensional Modeling with Validation Through Experiments,” Ph.D. Dissertation, University of Wisconsin-Madison, 2000. | |
Su J.C. , Kao J.Y., Tarng Y.S. , "Optimization of the electrical discharge machining process using a GA-based neural network", Int. J. Adv. Manuf. Technol. Vol.24,pp.81–90,2004 | |
Wang K., Gelgele H.L., Wang Y., Yuan Q., Fang M., "A hybrid intelligent method for modelling the EDM process", Int. J. Machine Tools Manuf. Vol.43,pp.995–999,2003 | |
Mr. Abolfazl Golshan
- Malaysia
gabolfazl@gmail.com
Mr. Mostafa Rezazadeh Shidar
- Malaysia
|
|
|
|
View all special issues >> | |
|
|